Видео

yes , we sometimes have to unplug and plug the power wire , I added Freon last year myself from local auto parts

@@boashna Thank I will give it a go in the morning...

Watch it on 2x video speed lol fast speed ,, I did it without instructions so can you ..

get it free from moein

It took me a year b4 I tried to take it a part ,,

yes - 7:29 shows it my light pointing at it

I did this and my freezer shows at -1 but needs to be at least-18 I just ordered the fan

that fan should last for ever - what makes you think fan is out

@@boashnathe Freezer is not working and the refrigerator is fine, the ice maker is also not making ice. I cleaned the filter from dust and cleaned the hose,

If too much fresh air enters the freezer area because seal was bad or door was open too long , freezer will ice up and stops working. Behind the fan there is a coil that may have ice on it. Make sure drain for coil located on center is cleared and clean. it is possible for you to unplug and deice without doing anything. Fan comes on when you plug the refrigerator in for few seconds on startup

boats that can go over 50 mph use 2 cables for safety, power steering uses one connection.

heat the nut, it will get larger and it will move easily

Make sure to use a earmuff for water supply . If p hole is not shooting water and no water at hub it may be a water pump . p hole pulls out with pliers it is plastic .. use pliers to pull it out and check for obstructions

bolts on lower units may need to be heated to come out as they can break off if stuck . THey are aluminium and take little force to move them.

unfortunately I don't try hoover hoover.com/pages/product-manuals

Good job

If you race the engine by going high and low on rpm quickly you get the rev limiter.. this is what the service book says Over-Revolution Caution System Condition: Yes Yes Yes Yes Yes No The ECM controlled over revolution limiter will engage at the engine speeds shown below. Once engaged it will initiate an intermittent fuel injection signal to reduce engine speed. Over revolution limiter DF100A/115A: 6 200 r/min. DF140A: 6 500 r/min. Action: Engine speed • Automatically reduced to approx. 3 000 r/min. by an intermittent fuel injection signal. • If the operator decreases the engine speed below the over revolution system maximum preset value, within 10 seconds, the over-revolution caution control will be canceled. Caution lamp Caution buzzer Reset: “REV-LIMIT” lamp lights continuously. No buzzer sounds. Close the throttle to reduce the engine speed below approx. 3 000 r/min for one second. 1A-8 Engine Control: Low Oil Pressure Caution System Condition: Immediate activation of the system when the oil pressure switch is turned “ON” due to an engine oil pressure drop below 100 kPa (1.0 kg/cm2, 14 psi.) while the engine is running. Action: Engine speed • Automatically reduced to approx. 1 000 r/min. maximum by an intermittent fuel injection signal. • The engine automatically stops 3 minutes after the caution system is activated. Caution lamp Caution buzzer • “OIL” lamp lights continuously. • “REV-LIMIT” lamp lights continuously during engine speed rev-limiter activation (1 000 r/min, or higher). • Sounds in a series of long (1.5 sec.) beeps. NOTE If the engine is automatically stopped due to the caution system, the engine can be started again. However, the caution system will repeatedly activate until the cause is eliminated. Reset: Stop the engine and check the engine oil level. Refill the engine oil to the correct level if it is below the low oil level mark. If the engine oil level is correct, the following causes may be considered: • Improper oil viscosity. • Malfunctioning oil pressure switch. • Clogged oil strainer or oil filter. • Worn oil pump relief valve. • Oil leakage from the oil passage. • Excessive wear/damage of oil pump. NOTE The low oil pressure caution system will reset when the oil pressure is restored to over 100 kPa (1.0 kg/cm2, 14 psi.) at approx. 1 000 r/min. or less engine speed operation. The engine must be stopped and checked immediately once the system is activated

does this happen on both switches and fully charged battery . a 140 hp is near 450lb and a pain to lift using 3 strong guys.

Bravo

Excellent!

Glad I could help!

when putting the plastic part in ,you may want to shift the gear to get a better position and when you finished to put the cover on you need to put it in N to be able to complete the job.

Bravo - now you can go boating and catch fish.

allen wrench goes through screen , tool and part are free from moen .

Mine was out of warranty so they won’t send the tool. Going to have to replace the faucet because wore out the internal teeth. Going with a different brand that doesn’t have a dumb set up

warranty is life time and use the 800 number to call them .. talk to them direct .. if you did buy a new item buy something that you can replace the filter quick .. since the filter needs to be replaced ..

go to 5:28 mark on this video

if nothing is working it is the ground wire. use a jumper cable and connect the red to the truck on one side and red to trailer to add more ground connection.

yes metric system

Free is good .

describe the alarm and light. does it happen when engine is cold, or does it happen when engine is warm. lowering engine makes fuel get to engine easier so if there is no alarm a dirty fuel filter or primer needs to be squeezed.

watch the video at 2x speed .. simple job. undo bolts and change gasket on anode. if you are in fresh water skip the work.

3 flash then 2 flash is map sensor 2 . Oil change is solid light on oil and intermittent beep sound . To reset oil change reminder, kill switch needs to be pulled out 3 times in 10 sec with iginistion in on postion and a long beep means reset completed. Neither one of above activate the maximum 3000rpm safety mode and engine will not be restricted above 3000 rpm . Buy a book on line as mentioned earlier on cheap.

@@boashna that didnt answer my question. Is the code checked with key foward? Or while motor is on?

motor running

@@boashna o ok thank you. Then i must only need an oil change.

ruclips.net/video/Xok_tvoXQbk/видео.html

OIl change at 100 hrs reminder. solid oil light along with beeping . After chnaging oil pull kill switch 3 times while powered and beeping in 10 sec to reset it. long beep means reset complete.

@@boashna its an old boat that i barely got. Motor is an 2005

just remeber that you dont need to fully disasemble the car to get the task done